Search results

  1. Davesmopar

    A500 OD spring stuck in Hub??

    A500 OD spring is completely collapsed inside OD hub, is it possible it is still under tension and stuck or just completely dead and not falling out, the bottom of the spring and OD hub are even.....
  2. Davesmopar

    RPM limit question?

    LA360 stock short block except for resized rods with ARP bolts.. forged pistons.... valve train aside... Do I need to stick to 6,000 shifts or would it be safe to 6,500 or maybe even 7,000 (he asked while cringing)???
  3. Davesmopar

    Transmission cooler question

    I'm going to be running a large transmission cooler.... 11" X 12" plate and fin type..... Stand alone or in series with radiator??? Running a 2500 stall....
  4. Davesmopar

    Axle end play???

    What is the proper fix for too much end play?? 8.75/spool.... both sides..
  5. Davesmopar

    Shock plate question

    Will these work for the ISO delete??? 8.75 into 76 Roadrunner
  6. Davesmopar

    8.75 swap backing plates question..

    Can I swap the 8 1/4 backing plates over to the 8.75 when I swap rear-ends???? 67 8.75 into 76 Roadrunner
  7. Davesmopar

    Fan shroud bolt size?????

    I am installing a fan shroud, not been using one, but it's getting hot out now..... I have a master tap and die set but nothing fits the radiator holes for the fan shroud... before I make my own holes can anyone tell me the correct bolt size???? 76 Roadrunner 360 radiator...
  8. Davesmopar

    One of these things is different than the others.....

    Well I guess it was going to happen sooner or later..... lol Using your weekend hotrod as a daily driver and playing very hard with it can be costly sometimes...
  9. Davesmopar

    904 slip yoke with 1350

    Does anyone know where to get a 904 slip yoke for 1350 u-joint???? That doesn't cost $200.00 + ......... And what do you think about the slip yoke having straps instead of being pressed in????
  10. Davesmopar

    Not sure where to put this question

    BudW you inbox is full.... please move this to were it goes.... Not ready for sale yet. I need to sell my A body rear end to pay for building my B body rear end I don't have a clue what to ask it..... would you happen to have any idea what to ask for it???? 8 3/4, 2.76 open...
  11. Davesmopar

    Ignition wire routing question....

    I am running Hooker Headers and want to know how others are running your ignition wires to number 5 and 7 plugs and straight or 90 degree boots..... I am Not looking for a better Header, I have to use these due to budget issues right now.....so please don't post about TTI headers etc. Etc...
  12. Davesmopar

    Clicking from bellhousing area

    Does anyone see anything wrong with the torque converter and or the flex plate???
  13. Davesmopar

    8 3/4 specs

    I'm about to start building this 8 3/4 rear end with a 489 case oh, I am going to go with a crush sleeve Eliminator kit + 1350 yoke... I am looking for the assembly specs with old bearings as well as new bearings....
  14. Davesmopar

    Thermoquad question

    Need help with choke pull off linkage..... Does it go like this one??? Or this one???
  15. Davesmopar

    Introducing New Member: Davesmopar

    I have owned many mopars including 3 fbodys. Including the 76 RR that I still have since 1987.... Location: Hendersonville, Tn
Back
Top