Search results

I ended up having a guy with a really nice diplomat police package buy a number of parts from me and eventually the rest of the vehicle was scrapped.

Sadly, repairs got too costly and while parked trying to sell some dummy pulled a hit and run on the driver door. She's got a wobble at front right, coolant leak at the timing cover and crummy tires up front. Had a freshly converted and charged AC, new alternator, optima yellow top batt and...

I'm starting a battery relocate project to coincide with installing powered seats in the car. Got some of the goodies in the mail today... :D I found this diagram online for integrating a Ford solenoid into a battery relocate with master cutoff switch which seems to have been designed around...

I glad you added this comment. I hadn't considered the implication of an always on, huge a$$ live wire running through the car. I've been doing some reading and it seems like I need to do quite a bit more planning on the wiring to do this right...

Thanks for the info BudW. I figured it was probably a big circuit because they wanted to be sure it could handle both seats under stallout and maybe moving in more than one plane at a time.

Ok, wiring complete on both seats and switches working as expected. I stopped by a metal fabrication shop today who agreed to work on the mounting system. Next step is to measure the amp draw for the seat on stall to determine the fuse rating needed. Diagram says 25 but not sure if that's for...

I'm thinking maybe a relay switch to deactivate all rear lighting on the vehicle. No particular reason... :rolleyes:

Still working on the wiring, should finish tomorrow. I had to eliminate wires and ended up needing to swap connectors from the old harness back to get the recline motor working due to 4 vs 6 pin. It was relatively easy as I was able to use a pick to free the pins and click them into place on...

Got the harness! Going to be some midnight soldering in store for me...

Got the high voltage switch, waiting on the harness which should arrive tomorrow.

I have also been considering installing a Havis police console. They obviously don't make one for the car but it's steel so it can be fabricated to fit. I got to know them while I worked as an installer building police vehicles for about 8 months. Would be a cool place to install a CB radio...

I wonder if there is space under the bottom of the storage compartment so you could use a profile gauge to fit the console to the trans tunnel contour. If so, this plus some plastic paint to color match wouldn't be too bad.

Just finished wiring up a quick disconnect into the seat wiring harness. Stripped back the tape, solder, heat shrink, electrical tape and friction tape. Hooked her up to the bench power and she chooches. I used an alternator wire extender, lol. It was cheap, did what I wanted and had a...

Hey, I resemble that remark!

It was about $1100 including freight shipping for the whole set. I felt good about this because the recaro seat I was looking at was about that much for one before shipping. I have not put them in yet but I will likely be dropping them in about two weeks from now. Looks like they should go...

I have one of these too, just aching to dump my beverage on the floor at the first chance. I was planning to weld a couple of bungs to the trans tunnel and tap them, affix the thing with screws. I abandoned this when I went for the buckets. Also, the ashtray conflicts with larger cups. So...

I definitely plan to add a center console to my car after the 300c SRT8 buckets are in. I haven't found anything that trips my trigger yet...

Since this is my only car, my plan is to make sure I can power the seats and then run a properly fused supply line into the seat area before starting on the physical anchoring. On these seats, there is a bottom and a top half to the mounting system. Bottom half bolts to the frame, top half...

I'm having a bit of a challenge installing these seats related to the electrical wiring for the driver's seat. The seat is powered through a memory seat module (MSM) but the connectors didn't come with the seat because they're part of the interior wiring harness which has separate salvage...

Got this part replaced and re-installed along with an 1156W LED, working wonderfully.

Like a BOSS. Thanks a bunch!

That looks like a different model, here is a diagram I found of the whole assembly, reflector/bulb socket are inside. I already have an LED one in hand. ;) I'm worried though that this may have been caused by a short.

Anyone know the part number for this piece and if it's still available for purchase or will I be salvage hunting? It's the reflector and bulb housing from the high mount brake light. Wasn't working when I got the car and I finally got around to replacing the bulb. Discovered that the bulb had...

Picked up these seats today to install in the G. Fury at some point in the near future. Wanted something more adjustable and with bolsters. Since these are from the 300C SRT8, still kind of keeps it in the family. Will re-cover them in tan leather/suede in the near future to match my car's...

I could re-use them, just thought if I'm buying the whole front suspension as a kit why not do that too. I understand they can wear and the bearing won't fit tight.